Predicting pavement performance using distress deterioration curves

Highway Authorities in the UK use Surface Condition Assessment for the National Network of Roads (SCANNER) in assessing and managing their road networks. This survey vehicle utilises laser measurements to detect and quantify most of the distress on the road surface, such as rutting, cracking and texture depth. It is however a data intensive and expensive approach since it is conducted annually. This study presents a simple method to predict pavement distress using previous SCANNER measurements. The previous measurements are used to develop Distress Deterioration Master Curves (DDMC) that relate distress deterioration rate with the severity of the distress. These curves can be used to predict future distress severity based on the current state without the need to provide further data such as pavement age or pavement material properties. To demonstrate the application of this method, a significant amount of SCANNER data covering around 400 km of class A roads in Nottinghamshire collected between 2014 and 2020 were analysed, and rutting, crack intensity, and texture depth were modelled in this study. DDMRs of these distress types were built based on data collected between 2014-2018, then 2020 data were used to validate the predictions. The results show that the developed method can be implemented in predicting surface distress of roads using previous measurements, which makes it a valuable addition tool for highway authorities subject to underfunding.

CONTACT Ahmed Abed abeda@aston.ac.uk Different methods have been developed to monitor and assess the surface condition of roads.In general, these methods can be categorised into two types, manual visual surveys, and automated surveys.In the UK, two visual survey methods are frequently used, Coarse Visual Inspection (CVI) and Detailed Visual Inspection (DVI) (Department for Transport, 2021).These methods are mainly applied nowadays to assess the condition of the unclassified road networks in the UK, the difference being that a CVI can be performed from a slow-moving vehicle whereas a DVI is a walked survey but more comprehensive and detailed than the CVI.On the other hand, automated surveys rely on laser sensor measurements and road surface images to assess road condition.Two automated Traffic Speed Survey (TTS) methods are implemented in the UK, Traffics Speed Condition Surveys (TRACS), which is mostly used on the trunk road network, and SCANNER, which is used by local highway authorities to scan class A, B and C roads (Department for Transport, 2021;Mcrobbie et al., 2007); A roads are major roads designed to link major areas, B roads feed traffic onto A roads from adjacent areas, and C roads are smaller links between villages, towns, or other housing or industrial areas (Department for Transport, 2012).
Apart from these two survey methods, there are numerous studies in the literature on road survey methods and the key issues with each method such as the accuracy of the measurements, survey speed, repeatability and reproducibility of the results (Chu et al., 2022;Ragnoli et al., 2018;Shtayat et al., 2020).Since this study is concerned with modelling pavement performance using SCANNER then this survey method is given more attention.Figure 1 shows the main components of a typical SCANNER vehicle; it has: two digital laser sensors that are used to capture surface distress, transverse profile, longitudinal profile, and edge condition of roads (UK Roads Board, 2011b).Some SCANNER vehicles implement artificial intelligence and image processing technologies to better identify the cracks (PTS, 2022).Over 40 indicators are extracted from the laser measurements, these include rutting, cracking, longitudinal profile variance, texture depth, and edge condition; the other indicators are basically different forms of reporting these distress types (UK Roads Board, 2011a).Highway authorities process these data to calculate one indicator, namely Road Condition Index using the following equation: where R LW , R RW are rutting scores in the left and right wheel paths, T is the texture depth score, CI crack intensity score, LPV is the longitudinal profile variance score over 3 or 10 metres, RW and IW are reliability and importance weightings that depend on the class of the road and can be found in (UK Roads Board, 2011a).The RCI is calculated for every 10 metres of the surveyed roads and based on its value the condition of the sections is ranked into three levels: green for RCI ≤ 40, orange for 40 < RCI ≤ 100, and red for RCI > 100; these ranks are used to manage the road network and plan maintenance activities.
On the other hand, various different methods have been developed to model pavement deterioration.Mechanistic models (Abu Al-Rub et al., 2012;Dinegdae & Birgisson, 2016) rely on methods such as fracture mechanics and constitutive modelling to predict pavement distress.Mechanistic-empirical models (ARA, 2004;Luo et al., 2017) combine the mechanistic response of pavement structures (i.e.stresses and strains) with empirical regression models to predict pavement performance.Empirical models use methods such as machine leaning or statistical regression to predict pavement performance (Kargah-Ostadi & Stoffels, 2015;Marcelino et al., 2019;Yu et al., 2007).Further, due to the stochastic nature of pavement performance (Darter & Hudson, 1973), researchers have also developed probabilistic methods to model pavement deterioration, such as Monte Carlo simulation (Abed et al., 2019;Wang et al., 2010), and Markov Chains (Abaza, 2015;Alimoradi et al., 2020); Artificial Neural Networks have also been widely applied in predicting pavement performance (Wang et al., 2022;Zhou  et al., 2021).Most of these methods however require various inputs such as material properties, pavement structural data, pavement age, climate data, or traffic data (Ziari et al., 2015), which may limit their implementation.
Highway authorities in the UK conduct annual road distress surveys to assess the condition of the road network, calculate RCI, and plan maintenance activities.This process however is expensive and time consuming, which exerts an additional economic burden on the already underfunded budget allocated for the maintenance of the roads.Therefore, the aim of this study is to develop a simple model capable of predicting the future condition of a pavement surface based on its current condition using a new approach called Distress Deterioration Rate (DDR).By this approach, the DDRs are calculated using previous SCANNER measurements depending on the severity of each distress, these are used to construct deterioration curves that can be used to predict the future level of the distress depending on its current level only.A similar approach has been suggested in literature to predict pavement deterioration rate expressed by a drop in Pavement Condition Index (PCI) by Kargah-Ostadi et al. (2019).In that study, the authors built a PCI deterioration curve in which the average drop in the PCI is dependent on the current PCI value.The PCI deterioration curve was built using the previous two measurements where the deterioration rate was calculated as the drop in the PCI divided by the time lag between the measurements.This study demonstrated that the PCI deterioration rate is low when the pavement condition is good (PCI > 90) and also when it is bad (PCI < 40).This is probably because the PCI score is scaled to be between 0-100 rather than because of a change in the deterioration rate of the distress types included in the PCI calculations.Accordingly, this method has been implemented in this study but with some modifications.Firstly, using two measurements to determine a deterioration rate may not be sufficient; the deterioration rate may vary considerably from one year to another, therefore obtaining the deterioration rate as an average of a longer period is more accurate.Secondly, the PCI is a function of various distress types, with each having a certain weight and reliability factors, and distress deterioration may increase, decrease, or remain constant over time.Accordingly, every distress should be modelled individually to exclude the effects of the other distress types, weighting and reliability factors on the Distress Deterioration Rate (DDR).Furthermore, based on the data collected in this study, we find that DDRs are functions of the current condition or deterioration level of the pavement.This means that a few deterioration models rather than one might be required to predict a distress type, where every model is required to fit certain distress severity data.Despite this approach being applicable, it is not practical as the number of models might be very high.To this end, we introduce in this study a novel method to construct a distress deterioration master curve from the individual DDR models.The distress deterioration master curve can then be used to predict the future level of the distress based on its current level.By implementing the suggested approach and the stated modifications, rutting, cracking, and texture depth have been selected to demonstrate the application of the suggested method.The results show that this approach has a reasonable accuracy and could be a valuable additional tool for highway authorities, allowing them to reduce their spending on pavement condition assessment.

Data description and pre-processing
In this study, a significant amount of SCANNER data from around 400 km of class A roads in Nottinghamshire were collected; Figure 2 presents a map showing a sample of these data.The data were supplied in a text file format as used in the UK Pavement Management System (UKPMS) software.The data are structured to report 44 data points that include distress measurements, different forms to express the distress, section geometries, and section coordinates of every 10 metres of the scanned network.The data cover the inner lane of one direction of the roads, which had been scanned every two years between 2014 and 2020, and they amount to about 40 thousand sections.A sample of the raw data is presented in Table 1.These data however may contain inherent issues such as error in measurements, missing data, spatial variability, inaccurate section boundaries, or even outliers which may happen due to localised issues such as drainage problems (Kargah-Ostadi et al., 2019), or even updating data analysis algorithms or SCANNER laser sensors over time.Another issue with the data is maintenance and rehabilitation activities which are manifested as improvements in the pavement condition or a reduction in distress levels.These issues can lead to a large bias in the calculations of DDRs and should be treated before attempting to build deterioration models.
Many methods to reduce the effects of these issues on the quality of data have been suggested in literature (Kargah-Ostadi et al., 2019), as shown in Table 2. Every one of these methods is suited to a specific issue in the data.For instance, if a set of data is missing, then an averaging or interpolation process can be followed to estimate the missing data.Likewise, if a dataset is suspected to have a measurement error or maintenance was provided, then the outlier removal method can fix this situation.In this study, two methods were followed to pre-process the data.Firstly, the sections that showed a reduction in distress level were filtered from the data using the outlier removal method.This is to exclude sections that might have received maintenance or might contain an error.Secondly, when joining sections from different years, some sections presented error at the boundaries.In other words, there was some distance difference in these sections from one year to another.This could be due to an error in identifying the start stations of roads, the temporal separation between the surveys which may affect sensor accuracy or analysis algorithm of sensor data, or survey staff change from one survey to another.To solve this issue, an outlier removal based on the distance was applied; basically, the sections that showed a difference in the distance of more than a threshold value of 5 m measured centre to centre, which is 50% of a section length, were excluded from the data; this is to assure that the same section is being monitored over time.Lastly, there was no concern about spatial variability in the data since the maximum section length was 10 m, and it is quite unlikely in this length that a significant change in pavement condition occurs.Following these techniques, the data was pre-processed and used in building deterioration models as explained in the following section.

DDR model development
Pavement distress increases over time due to traffic loading and environmental conditions such as ageing and thermal stresses.If the distress is surveyed repeatedly over a period of time, and in the absence of intrinsic pavement modelling inputs such as material properties and pavement design, then one can adopt a mathematical approach to model the rate of distress deterioration, as follows: where DDR is distress deterioration rate, D is the distress magnitude, i is the survey number, and T is the time of the survey.The data in this study however show that DDR is not linear; rather it is dependent on the magnitude or severity of the distress, or pavement structural condition in general (Abaza, 2014).Therefore, the previous equation can be rewritten as follows: where s is the severity of the distress in question.This equation can be used to calculate the DDR considering the current structural condition or the distress severity, which in turn can be used to predict the distress magnitude as follows: where PP is the required prediction period in years.The application of this equation seems straightforward but relying on two surveys to estimate the DDR may not reflect the actual deterioration; also, it will not reflect the variability in the DDR from one section to another due to the variation of material properties for instance.Accordingly, it is suggested in this study to determine the DDR of a distress as an average of more than two previous measurements, which then can be utilised in predicting the future magnitude of that distress using the last survey results and the required prediction period by applying Equation (3). Figure 3 presents a flowchart explaining the developed methodology and how it can be implemented to determine DDRs and utilise these in predicting future distress levels.It must be stated here that the deterioration curves might be linear or nonlinear.This depends on the way the individual DDRs collapse onto each other to form a master curve; if the trend of the master curve is linear then a linear model should be fitted; if the trend is not linear then a suitable model should be fitted based on expert judgment.

Distress deterioration rates
Following the methodology explained in the previous section the average DDRs of the three selected distress types, rutting in the left and right wheel paths, crack intensity over the whole carriageway, and texture depth, were determined as shown in Figures 4-7. Figure 4 and Figure 5 show the DDRs of rutting in the left and right wheel paths respectively.Interestingly, these figures show an approximately linear relationship between the average rutting of the sections of every group.They also show that the deterioration rate, which is expressed by the slope of the fitted lines, increases slightly with the increase of rutting severity.This can be explained by the fact that severe distress reduces the structural capacity of pavements, which leads to larger strain levels and eventually larger distress.It must be mentioned here that the rutting in the left wheel path did not correlate well with the rutting in the right wheel path, with a coefficient of correlation (R2) less than 0.2.This can probably be explained by factors affecting rutting on roads such as effects of the cross slope on the distribution of traffic loading on the pavement, and on drainage where the lower side of a lane may become more saturated and eventually weaker than the higher side.Accordingly, two rutting models for the two wheel paths have been developed in this study as explained in later sections.
Figure 6 shows the deterioration trends of crack intensity over time.This figure demonstrates that cracking does not increase linearly but tends to take an exponential form.This means that cracking DDRs can be more progressive than other distress types such as rutting especially at high crack severities.The reasons behind this can be factors such as ageing which reduces strain tolerance of asphalt, pavement water damage once cracks are initiated, or general deterioration in the structural capacity of a pavement over its service life.
Lastly, Figure 7 presents the deterioration trends for texture depth; it can be seen that texture depth generally decreases over time.This is a normal trend for texture depth as it decreases due to abrasion of the pavement surface caused by vehicle tyres (Athiappan et al., 2022).The decrease rate, however, is dependent on the texture depth; the figure shows that sections with large initial texture exhibit faster reduction in texture depth than those with low texture.This is mostly like due to the larger the texture depth the bigger the frictional forces with vehicle tyres.
The above analysis is based on average DDRs.The variability amongst deterioration rates, however, could be large.This could be due to several factors including variability in traffic loading, pavement    structure, properties of pavement layers, environmental conditions, or even pavement geometry such as longitudinal and transverse profiles.The work presented in reference (Kargah-Ostadi et al., 2019) is based on the average deterioration in the PCI.The data collected in this study, however, shows that there is a large variability in deterioration rates.For instance, Table 3 indicates that the level of rutting variation in both wheel paths is from 6.7% to 61.3%.This means there is significant variability in the DDRs, and therefore this should be considered in the prediction process.To achieve that, three DDRs were developed for every distress type; the first represents the average deterioration, the second fits the 10th percentile of each severity group, the third represents the 90 th percentile.The 10th and 90 th percentiles were calculated by fitting a lognormal distribution and determining the distress values that match these reliability levels.Accordingly, three deterioration models are developed for every distress type, one at the average deterioration rate, one below the average which can be considered an optimistic prediction, and one above the average which accounts for a high level of deterioration around the worst-case scenario.

Distress deterioration master curves
The deterioration curves shown above can be applied directly to predict the future level of a particular distress type using Equation 3. Basically, one can use a suitable deterioration rate based on the current level of distress and the required prediction period.This means however that several deterioration curves should be used in the prediction process.Although this is achievable, a new method has been developed in this study to generate a single Distress Deterioration Master Curve (DDMC) that can be used in the prediction process.
By analysing the results in Figures 4-7 it can be seen that the distress results of individual groups can be collapsed onto one master curve.This can be achieved by shifting the x axis data to the right until all data form a smooth curve.The concept behind this idea is that the models of the individual groups can be represented by a single master model in which the slope of the master model matches the slopes of the individual models.In this case the deterioration rate of the individual groups, which is the slope of the individual lines, will match the deterioration rate of the fitted master curve.Caution should be taken when constructing master curves of this type as data shifting should be performed without changing the slope of the data.This has been accomplished by manually shifting the survey data to the right relative to the first group (lowest distress level) until a smooth curve is achieved.For example, the 2-4 mm group in Figure 4 was shifted to the right until this dataset formed a smooth line with the 0-2 mm group; all other groups were similarly shifted to the right until all of the groups formed a smooth line.It must be stated here that when shifting a data group to the right, the whole group is shifted to the right while maintaining a time difference of two years between the data points of that group, as the frequency of the surveys is one every two years.The y axis data on the other hand is kept the same when shifting the data, as shown in Figures 8-11.The exact same procedure is followed when constructing DDMCs at any selected reliability level.For example, to construct a deterioration master curve at 90% reliability level 90 th percentiles of the data are used rather than averages, and these are grouped based on severity.The data of every severity group are then shifted to the right until a smooth curve is obtained as explained above, and lastly a suitable DDMC is fitted.Figure 8 and Figure 9 show the DDMCs for rutting in the two-wheel paths.These figures show the average deterioration rates as well as the 10th and 90 th percentiles.The main point to observe here is the closeness between the individual data sets and the master curves.If these two match each other, then the master curve will give good results.It must be mentioned here that despite Figure 4 and Figure 5 showing that rutting DDRs may increase over time, the largest increase is about 0.08 mm/year for rutting in the left wheel path and 0.2 mm/year for rutting in the right wheel path.Accordingly, linear models were fitted to the shifted data to model rutting deterioration behaviour, as shown in Figure 8 and Figure 9. Based on these figures, the DDRs in the left wheel path are 0.19, 0.52, and 0.95 mm at 10%, average and 90% reliabilities respectively, and 0.21, 0.46, and 0.79 mm in the right wheel path.
Following the same approach, DDMCs of crack intensity have been developed, as shown in Figure 10.In this figure, exponential models of the form (a × exp(b × x) − c) have been found to best fit the cracking data, with a coefficient of regression (R 2 ) greater than 0.95.This means that the deterioration rate for crack intensity is not linear but exponential related to the current intensity of the cracks.Lastly, Figure 11 presents the texture depth DDMCs, which shows that an exponential model provides    a very good fit with an R 2 of 0.98, except at 90% where the R 2 drops to 0.888, which still acceptably good.It must be stated here that the x-axis of the figures represents an 'imaginary' time with no absolute meaning; distress rate should be calculated based on the current distress level by inverting the deterioration models, as explained below.
The master curves can now be applied to predict the future level of distress by using the current distress measurements.With respect to rutting prediction on both wheel paths, Equation 3 can be applied directly using rutting DDRs at the selected reliability levels.With respect to crack intensity and texture depth the prediction process is less straightforward, because the deterioration rate is dependent on the level of distress.This can be calculated from the deterioration curves as follows: (1) Fit a curve to best match the behaviour of the data on the master curve; for the average crack intensity, the model below has been fitted: where CI i is the crack intensity at the current state.(2) By inverting Equation (4), the imaginary time associated with the current distress state can be calculated using the current distress measurement, as shown below: (3) By adding the required prediction period to the results of Equation ( 5) and substituting the outcome to Equation (4), we obtain the following equation: Following the above steps, the crack intensity deterioration model at 10% and 90%, as well as the texture depth deterioration models at 10%, average, and 90% have been derived as shown in Table 4.The following section discusses the implementation of the developed deterioration curves in predicting pavement performance and any limitations associated with this method.

Distress prediction results
To demonstrate the application of the developed DDMCs and analyse their predictive accuracy, rutting in both wheel paths, crack intensity, and texture depth in 2020 were predicted based on the data  9TD * i+1 = 2.4552 × e −0.056×(− Ln(TD i /2.4552) /0.056+PP) 10% Equation 10TD i+1 = 2.0262 × e −0.094×(− Ln(TD i /2.0262) /0.094+PP)Average Equation 11TD i+1 = 1.6471 × e −0.199×(− Ln(TD i /1.64711) /0.199+PP) 90% Equation 12* TD stands for texture depth collected in 2018.With respect to rutting prediction Equation (3) was applied directly by using the deterioration rates shown in Figure 8 and Figure 9, whereas for crack intensity and texture depth, Equations (7-12) were used.The prediction results are presented in Figure 12.This figure presents the measured distress from SCANNER in 2020 compared with the predicted distress using the deterioration models.It must be stated here that the 2018 SCANNER data was pre-processed using the outlier removal method to remove the sections that were maintained between 2018 and 2020, and also to remove sections that exhibited extreme deterioration, which may have been due to localised issues on the roads (Kargah-Ostadi et al., 2019).In this study, any deterioration more than two standard deviations above the mean was considered an outlier and excluded in the validation process.In practical applications of this work, pavement managers should have a record of any maintenance works that have taken place and any localised issues on their road network that can cause excessive deterioration in certain sections.These data will allow managers to remove these sections in the prediction process, and this will allow for a better implementation of the models.
Following these rules, the DDMCs were applied to predict the distress in 2020 at the selected reliability levels.Figure 12 A to F show rutting prediction results in both wheel paths at the selected reliability levels.The results in subfigure A were calculated by applying a deterioration rate of 0.1818 mm/year (as shown in Figure 8) in Equation ( 3), whereas a deterioration rate of 0.5158 mm/year was used in subfigure B, and a deterioration rate of 0.9462 mm/year was used in subfigure C. The deterioration rates applied in subfigures D, E and F are shown in Figure 9. Generally, these figures indicate that the larger the reliability level, the more the data shifted above the equality line.This is explained by the fact that at the 10th percentile, the deterioration rate will be below the average, which means the models will underestimate distress deterioration, whereas at the 90 th percentile, the deterioration rate will be above the average, which means the models will overestimate the deterioration rates.Similar trends can be seen for crack intensity in Figure 12 G to I, and for the texture depth in Figure 12 J to L. The difference between rutting prediction and crack intensity/texture depth prediction is that the deterioration rate in rutting is constant at a given reliability level, whereas it is variable and dependent on the current distress state in the case of crack intensity and texture depth.Furthermore, to assess the statistical significance of the results, the Root Mean Square Error (RMSE) and R 2 were calculated, as shown in Table 5, which also presents the number of road sections used in the validation process.It can be seen that there is a generally good correlation between the measured and predicted data.
To further understand the accuracy of the predictions, it is necessary to set up some measures that can describe the accuracy in a more informative way.R 2 and RMSE are statistical measures that show how aligned and close the predictions are to the actual measurements in a macro sense.But to understand more about the accuracy of the predictions and analyse to what extent the models performed in an acceptable or unacceptable way, it is necessary to consider further measures that can give a deeper sense of the data.To achieve that, four descriptive measures have been considered in this study, these  are Excellent, Good, Poor, and Unsatisfactory.Every category of these measures has a predetermined absolute error; if the absolute error in the prediction data is smaller than the predetermined error, then that data set will be assigned to that specified category.In this case the results will be expressed as the percentages of the data matching the selected descriptive measures.The only issue with this approach is the values of the predetermined absolute errors.These error thresholds can significantly affect the interpretation of the results; therefore, they should be selected carefully.If they are too tight, then the results will be entirely unacceptable and vice versa; and unfortunately, no thresholds have been reported in the literature.Accordingly, the thresholds shown in Table 6 were selected based on expert judgement after careful consideration.Rutting prediction with an error up to 1 mm or crack intensity prediction with an error up to 0.25% or texture depth prediction with an error up to 0.15 mm are considered excellent predictions.Rutting prediction with an error more than 3 mm, crack intensity prediction with an error more than 0.75% or texture depth prediction with an error more than 1 mm are considered unsatisfactory predictions.Acceptable and poor prediction thresholds are between these extremes.Following this approach, the micro accuracy of the predictions, which is here defined as the accuracy of the individual predictions rather than the model as a whole, was analysed, as shown in Figure 13; this figure presents the percentages of the road sections that fall under the four descriptive measures.With respect to rutting, in general about 85-83% of the predictions fall under excellent to good predictions in both wheel paths.The texture depth showed the best prediction accuracy with 93% falling under excellent.Crack intensity, however, shows that 61% of the predictions fall in the poor or unsatisfactory categories.This is most likely due to the quality of the distress measurement data which has been reported as the most difficult one to quantify due to the similarity between this distress and other features on the road surface such as patches, fretting, ironwork, and high friction surfaces (McRobbie & Wright, 2006), which makes the quality of the crack intensity data less than the quality of other distress types.

Conclusions
In this study, an innovative practical method to model pavement deterioration using SCANNER data has been developed.This method utilises previous distress measurement data to estimate distress deterioration rates (DDRs) as a function of distress severity and use these to predict pavement performance.DDRs were determined by analysing SCANNER measurement data and grouping the distress into different levels based on their severity, modelling each group individually, combining the developed individual models into one deterioration model.To demonstrate the application of this method, a significant amount of SCANNER data for A roads in Nottinghamshire were employed in this study.The data were used to determine the DDRs of three main distress types: rutting, cracking, and texture depth.The DDRs were then used to predict distress in 2020 based on data collected in 2018.Based on the results of this study, the following conclusions can be drawn: 1.The developed method requires previous distress measurements to predict future condition; no data about pavement type, age or material properties are required, which makes it practical and easy to implement.But the prediction accuracy of this method relies significantly on the quality of the collected data.2. The distress prediction results showed different levels of accuracy from excellent to unsatisfactory.
This can probably be explained by factors such as: variability of pavement response from one place to another, variability of pavement properties, effects of pavement maintenance on distress measurements, the accuracy of distress quantification and the uncertainty of the overall process.3. Unlike Markov Chain methods, this method can be used to model pavement performance at both network level and project level, and it can be used to predict the performance of individual sections and locate those requiring maintenance or further investigation.4. Three distress predictions have been modelled in this study, at 10th percentile, average, and 90th percentile deterioration rates.The first is an optimistic prediction, the second is realistic and may produce the lowest error in the prediction process, the last may overestimate the deterioration rate, but this may be desirable when making pavement management and maintenance plans, to be on the safe side. 5.Although this method was developed based on A roads in Nottinghamshire, UK, the methodology to extract distress deterioration curves is valid for all road classes and for all distress types.This means that a tailored set of deterioration curves can be developed for every authority reflecting the environmental conditions of their region, material properties, their pavement structures and traffic volumes.
The current work has been conducted based on a static prediction of distress deterioration; thus, a certain deterministic deterioration is assigned to the current distress state to predict the future.Future work will focus on developing a dynamic deterioration prediction model, in which the deterioration rate will not be a constant value but a dynamic one estimated based on the distress deterioration probability distribution function and past SCANNER data.

Figure 2 .
Figure 2. A map showing the study area and the road sections used in this study (The shown points represent the scanned road sections; bridges, roundabouts, and intersections were not included in the survey).

Figure 3 .
Figure 3. Flow chart explaining the methodology of the study.

Figure 4 .
Figure 4. DDRs for rutting in the left wheel path.

Figure 5 .
Figure 5. DDRs for rutting in the right wheel path.

Figure 6 .
Figure 6.DDRs of the crack intensity over the whole carriageway.

Figure 7 .
Figure 7. DDRs of the texture depth in the case of increasing texture over time.

Figure 8 .
Figure 8. Deterioration curve for rutting in the left wheel path.

Figure 9 .
Figure 9. Deterioration curve for rutting in the right wheel path.

Figure 10 .
Figure 10.Deterioration curve for cracking over the whole carriageway.

Figure 12 .
Figure 12.Distress predictions for year 2020 based on data collected in year 2018

Table 1 .
Sample of the raw SCANNER data used in this study.

Table 3 .
Rutting data in the left and right wheel paths collected between 2014 and 2018.

Table 5 .
Number of sections used in the validation process with, MSE, and R2 results.

Table 6 .
Criteria considered to rank the accuracy of the distress predictions.Figure 13. Pie chart illustrating the ranking of the predicted distress accuracy.